Samson S2000 Instruções de Operação Página 91
- Página / 124
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Hardware errors
Error codes – Recommended action Condensed state alarm active, when prompted, Err appears.
When fault alarms exist, they are displayed here.
62
x signal Determination of the measured data for the actuator has failed.
Conductive plastic element is defective.
The positioner continues to run in emergency mode, but should
be replaced as soon as possible.
The emergency mode on the display is indicated by a blinking
closed-loop operation icon and 4 dashes instead of the position
indication.
Note on the closed-loop operation:
If the measuring system has failed, the positioner is still in a reli
-
able state. The positioner switches to emergency mode where the
position cannot be accurately controlled anymore. However, the
positioner continues operation according to its set point signal so
that the process remains in a safe state.
Status classification
[Maintenance demanded]
Recommended action
Return the positioner to SAMSON AG for repair.
64
i/p converter The circuit of the i/p converter has been interrupted.
Status classification
Maintenance alarm (cannot be classified)
Recommended action
Cannot be remedied.
Return the positioner to SAMSON AG for repair.
EB 8384-4 EN 91
Code list
- Mounting and 1
- Operating Instructions 1
- EB 8384-4 EN (1300-1613) 1
- EB 8384-4 EN 3 3
- EB 8384-4 EN 5 5
- Vent opening 6
- 2 Article code 7
- 3 Design and principle of 8
- 3.1 Additional equipment 9
- 3.2 Communication 10
- 3.2.1 Configuration using 10
- TROVIS-VIEW software 10
- 3.3 Technical data 11
- 12 EB 8384-4 EN 12
- 4 Attachment to the control 14
- 4.1 Direct attachment 16
- 4.1.1 Type 3277-5 Actuator 16
- 4.1.2 Type 3277 Actuator 18
- 4.2 Attachment according to 20
- IEC 60534-6 (NAMUR) 20
- 4.3 Attachment according to 22
- VDI/VDE 3847 22
- Actuator stem 24
- EB 8384-4 EN 25 25
- 4.4 Attachment to Type 3510 28
- Micro-flow Valve 28
- 4.5 Attachment to rotary 30
- 4.5.1 Heavy-duty version 32
- 4.6 Reversing amplifier for 34
- 4.6.1 Reversing amplifier 34
- (1079-1118 or 1079-1119) 34
- From the positioner 35
- Control signals to 35
- 4.7 Attaching an external 36
- 4.7.1 Mounting the position 36
- 1.1, 1.2 14.1 3 14 99.1 38
- 4.7.3 Mounting the position 39
- 2 1 1.1, 1.2 40
- 4.9 Air purging function for 41
- 4.10 Mounting parts and 42
- 44 EB 8384-4 EN 44
- Table 6 · General accessories 45
- 46 EB 8384-4 EN 46
- 5 Connections 47
- 5.1 Pneumatic connections 47
- 5.1.1 Signal pressure gauges 47
- 5.1.2 Supply pressure 47
- 5.2 Electrical connections 48
- EB 8384-4 EN 49 49
- 24 V DC BE1 BE2 50
- EB 8384-4 EN 51 51
- 52 EB 8384-4 EN 52
- Connections 52
- 6 Operator controls and 53
- 7 Start-up – Settings 56
- 7.1 Defining the valve closed 56
- 7.3 Adapting the display 57
- 7.5 Checking the operating 58
- Manual reference variable 59
- EB 8384-4 EN 59 59
- 7.6 Initialization 60
- Default No 65
- Nominal range 65
- (locked with Code 4 = No) 65
- EB 8384-4 EN 65 65
- 7.7 Zero calibration 68
- 7.8 Reset to default values 68
- 7.10 Setting the bus address 69
- 8 Operation 70
- 8.1 Enabling and selecting 70
- 8.2 Operating modes 71
- 8.2.1 Automatic and manual 71
- 8.3 Malfunction/maintenance 73
- Error caused by pin 74
- 9 Adjusting the limit switch 75
- 10 Maintenance 78
- 12 Firmware update (serial 78
- EB 8384-4 EN 79 79
- 14 Code list 80
- Code list 81
- 82 EB 8384-4 EN 82
- 84 EB 8384-4 EN 84
- 86 EB 8384-4 EN 86
- EB 8384-4 EN 87 87
- Initialization errors 88
- 88 EB 8384-4 EN 88
- Operational errors 90
- 90 EB 8384-4 EN 90
- Hardware errors 91
- Error appendix 92
- 92 EB 8384-4 EN 92
- Data errors 93
- 94 EB 8384-4 EN 94
- Diagnosis errors 95
- 15 Dimensions in mm 96
- EB 8384-4 EN 97 97
- Heavy-duty version 98
- Light version 98
- EB 8384-4 EN 100
- 102 EB 8384-4 EN 102
- EB 8384-4 EN 103 103
- 104 EB 8384-4 EN 104
- EB 8384-4 EN 105 105
- 106 EB 8384-4 EN 106
- EB 8384-4 EN 107 107
- 108 EB 8384-4 EN 108
- EB 8384-4 EN 109 109
- 110 EB 8384-4 EN 110
- EB 8384-4 EN 111 111
- 112 EB 8384-4 EN 112
- EB 8384-4 EN 113 113
- 114 EB 8384-4 EN 114
- EB 8384-4 EN 115 115
- EB 8384-4 EN 117 117
- Model 3730-43 118
- or 3730-53 118
- EB 8384-4 EN 119 119
- 122 EB 8384-4 EN 122
- EB 8384-4 EN 123 123
Manuais e produtos relacionados com Amplificadores áudio Samson S2000
(16 páginas)
(60 páginas)
(5 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.077 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais