Samson S2000 Instruções de Operação descarregar pdf (Página 87)

Note: The error codes listed in following appear in the display corresponding to their status

classification set over the condensed state (Maintenance required/Maintenance demanded:

, Maintenance alarm: ). If “No message” is assigned to the error code as the status

classification, the error is not included in the condensed state.

A status classification is assigned to every error code in the default setting. The status classifi

cation of error codes can also be changed as required using an operating software (e.g.

TROVIS-VIEW).

EB 8384-4 EN 87

Code list

1 2 ... 82 83 84 85 86 87 88 89 90 91 92 ... 123 124

Mounting and 1
Operating Instructions 1
EB 8384-4 EN (1300-1613) 1
EB 8384-4 EN 3 3
EB 8384-4 EN 5 5
Vent opening 6
2 Article code 7
3 Design and principle of 8
3.1 Additional equipment 9
3.2 Communication 10
3.2.1 Configuration using 10
TROVIS-VIEW software 10
3.3 Technical data 11
12 EB 8384-4 EN 12
4 Attachment to the control 14
4.1 Direct attachment 16
4.1.1 Type 3277-5 Actuator 16
4.1.2 Type 3277 Actuator 18
4.2 Attachment according to 20
IEC 60534-6 (NAMUR) 20
4.3 Attachment according to 22
VDI/VDE 3847 22
Actuator stem 24
EB 8384-4 EN 25 25
4.4 Attachment to Type 3510 28
Micro-flow Valve 28
4.5 Attachment to rotary 30
4.5.1 Heavy-duty version 32
4.6 Reversing amplifier for 34
4.6.1 Reversing amplifier 34
(1079-1118 or 1079-1119) 34
From the positioner 35
Control signals to 35
4.7 Attaching an external 36
4.7.1 Mounting the position 36
1.1, 1.2 14.1 3 14 99.1 38
4.7.3 Mounting the position 39
2 1 1.1, 1.2 40
4.9 Air purging function for 41
4.10 Mounting parts and 42
44 EB 8384-4 EN 44
Table 6 · General accessories 45
46 EB 8384-4 EN 46
5 Connections 47
5.1 Pneumatic connections 47
5.1.1 Signal pressure gauges 47
5.1.2 Supply pressure 47
5.2 Electrical connections 48
EB 8384-4 EN 49 49
24 V DC BE1 BE2 50
EB 8384-4 EN 51 51
52 EB 8384-4 EN 52
Connections 52
6 Operator controls and 53
7 Start-up – Settings 56
7.1 Defining the valve closed 56
7.3 Adapting the display 57
7.5 Checking the operating 58
Manual reference variable 59
EB 8384-4 EN 59 59
7.6 Initialization 60
Default No 65
Nominal range 65
(locked with Code 4 = No) 65
EB 8384-4 EN 65 65
7.7 Zero calibration 68
7.8 Reset to default values 68
7.10 Setting the bus address 69
8 Operation 70
8.1 Enabling and selecting 70
8.2 Operating modes 71
8.2.1 Automatic and manual 71
8.3 Malfunction/maintenance 73
Error caused by pin 74
9 Adjusting the limit switch 75
10 Maintenance 78
12 Firmware update (serial 78
EB 8384-4 EN 79 79
14 Code list 80
Code list 81
82 EB 8384-4 EN 82
84 EB 8384-4 EN 84
86 EB 8384-4 EN 86
EB 8384-4 EN 87 87
Initialization errors 88
88 EB 8384-4 EN 88
Operational errors 90
90 EB 8384-4 EN 90
Hardware errors 91
Error appendix 92
92 EB 8384-4 EN 92
Data errors 93
94 EB 8384-4 EN 94
Diagnosis errors 95
15 Dimensions in mm 96
EB 8384-4 EN 97 97
Heavy-duty version 98
Light version 98
EB 8384-4 EN 100
102 EB 8384-4 EN 102
EB 8384-4 EN 103 103
104 EB 8384-4 EN 104
EB 8384-4 EN 105 105
106 EB 8384-4 EN 106
EB 8384-4 EN 107 107
108 EB 8384-4 EN 108
EB 8384-4 EN 109 109
110 EB 8384-4 EN 110
EB 8384-4 EN 111 111
112 EB 8384-4 EN 112
EB 8384-4 EN 113 113
114 EB 8384-4 EN 114
EB 8384-4 EN 115 115
EB 8384-4 EN 117 117
Model 3730-43 118
or 3730-53 118
EB 8384-4 EN 119 119
122 EB 8384-4 EN 122
EB 8384-4 EN 123 123

Comentários a estes Manuais

Sem comentários

Samson S2000 Instruções de Operação Página 87

Comentários a estes Manuais

Manuais e produtos relacionados com Amplificadores áudio Samson S2000